Information About Asbestos and The Hazard of Asbestos

Fiberquant Analytical Services
Phoenix, Arizona

 

Contents

1. The Hazard of Asbestos
2. Common Materials that Contain Asbestos
3. A Limited Survey
4. Your House Probably Has Asbestos If…

Written by Larry S. Pierce: 8-89

Last Revised: 2-26-98

1. THE HAZARD OF ASBESTOS

The hazard that asbestos-containing materials (ACM) presents to inhabitants of a building is primarily an airborne hazard. Asbestos fibers may be released from the materials, become entrained in the air of the building, be inhaled by an inhabitant, and lodge in the bronchia or lungs. Once there, the asbestos fibers do not ever escape and it is thought that even small amounts can eventually produce lung cancer or mesothelioma, a lung-lining cancer. ( Another asbestos disease, asbestosis, requires much larger amounts of asbestos in the lungs than could be produced in a residence or a workplace that is not involved in the asbestos business). Asbestos cancers have a long latency period, 20-30 years, so that young people have a greater chance to be affected in their lifetime than older people.

A number of asbestos or asbestos-like minerals are regulated. The most common type of asbestos encountered is called “serpentine asbestos”, which consists of the mineral chrysotile. It is considered the least toxic of the asbestos minerals. Less commonly encountered is a group of amphibole minerals, including “amosite” (not a mineral but a mixture of the minerals grunerite and cummingtonite), and the minerals crocidolite, anthophyllite, tremolite and actinolite. The amphiboles occur in nature both as fibrous or asbestiform varieties and as non-fibrous varieties. All the fibrous varieties of the above amphiboles are regulated by both the EPA and OSHA. The non-fibrous varieties of the amphiboles are not regulated by the EPA or OSHA. The fibrous amphiboles are considered to be more toxic than chrysotile, and are also more likely to become airborne, due to their brittleness and shorter fiber length.

For regulatory purposes, the Environmental Protection Agency (EPA) and OSHA have defined an asbestos-containing material as one which contains greater than 1% asbestos. Materials having 1% or less asbestos are considered to be non-asbestos-containing materials. The accepted method of determining whether a sample of a material contains greater than 1% asbestos and the type of asbestos present utilizes a polarizing light microscope. The sample is examined first at a magnification of about 10. Then examples of each fiber type observed, and/or a representative portion of the sample are mounted in oils of varying refractive index in order to document the optical properties of the fibers. The optical properties are usually sufficient to distinguish the asbestos types from interfering fibers, such as cellulose and fibrous glass. At Fiberquant, fibers not definitively identified by polarized light are further analyzed using scanning electron microscopy/energy dispersive spectrometry or by transmission electron microscopy/energy dispersive spectrometry. Certain samples may also be quantified using x-ray diffraction.

The presence of asbestos in a material does not always pose a significant hazard. Some substances are easily crumbled or reduced to powder by hand pressure, termed “friable”, whereas others do not produce powder by hand pressure, “non-friable”. A friable material would be more likely to produce airborne fibers than a non-friable material. Also, a damaged or broken material would be more likely to produce airborne fibers than one in good condition. Even a normally non-friable material can produce airborne fibers when highly damaged or abraded. These factors are all to be considered before deciding what the hazard of a given material is, or the course of action to use in dealing with that material.

Once asbestos is determined to be present in a material, several options of dealing with the material are possible. The first option would be to leave the material as is and untouched. This is often the option of choice for non-friable materials, materials which are in non-public areas and therefore only affect a few workers trained in asbestos hazards, and materials which are isolated from human contact. A second option is encapsulation, which in its broadest definition means to enclose the material without removing it. The enclosure can consist of a constructed barrier, for instance, of finished drywall over a surface coating, or of painted canvas over pipe insulation. Alternatively, the encapsulation can be a sprayed polymer of two types: penetrating encapsulant, which soaks into the material it is sprayed on, and bridging encapsulant, which only seals the surface, like paint. Even though the release of fiber is minimized or eliminated with encapsulation, the asbestos is still present, and the potential for fiber release always exists. In many cases, the asbestos will have to be removed anyway at a later date as per NESHAP (see below). The third option is removal, in which the asbestos-containing material is scraped off, chipped off or otherwise gotten rid and taken out of the building. Preparation of the building so as to prevent contamination of the premises is extensive and disposal of the material is expensive, so removal is the least economical of the three options. It has the advantage that the asbestos is for the most part gone (except those parts of the building that are inaccessible.

At present, there are no Federal or Arizona State laws requiring the encapsulation or removal of asbestos-containing materials in order to occupy a building. However, the Occupational Safety and Health Administration (OSHA) prohibits occupation of a work area (without respiratory protection) if either 1) the eight hour average fiber concentration exceeds 0.1 fibers/cc or 2) a 30-minute fiber concentration exceeds 1.0 fibers/cc. Neither of these levels is likely to be exceeded during normal building occupation unless heavy damage is inflicted to a asbestos-containing material. The National Emission Standards for Hazardous Air Pollutants (NESHAP), a Federal law, prohibits the renovation or demolition of greater than either 160 square feet of asbestos-containing surfacing material, or 260 linear feet of asbestos-containing pipe insulation without adequate precautions against fiber release. For friable materials, this means that renovation is done by an abatement contractor and demolition is only allowed after the material has been removed. Therefore, removal of friable asbestos-containing materials will be required during some point in a building’s lifetime, if only at the end. Non-friable materials can fall under NESHAP regulations if they can become friable during the renovation or demolition. Naturally, becoming friable is highly dependent upon the exact type and constitution of the material in question in addition to how it is handled. Whether a non-friable material will be regulated must be decided on an individual basis.

2. THE HAZARD OF INDIVIDUAL TYPES OF ASBESTOS-CONTAINING MATERIALS

Many different types of building materials at one time contained asbestos, such as beam spray, ceiling tile, floor tile, mastic and glue, etc. Each type has distinct properties, hazards and possible courses of action. To be discussed here are: a) beam spray, b) ceiling acoustical texture, c) joint compound and wall texture, d) floor tile, e) mastics, f) hard glue, g) ceiling tiles, h), pipe or thermal system insulation, and i) roofing.

A. BEAM SPRAY

Metal structural members in multi-story buildings are required to be sprayed with an insulating layer that will provide several hours of evacuation time during a fire before the members sag or collapse. During the years ~1935-1970, asbestos, usually chrysotile asbestos, was commonly a component of beam sprays. The typical such spray has a medium friability.

If enclosed or isolated in areas in which damage is unlikely, such a spray would not represent a very high hazard. Unfortunately, the usual situations encountered are: 1) beam spray exposed on vertical beams in storage areas, subjected to scraping and bumping, 2) beam spray above dropped ceilings, where ducts, telephone wire, etc. are installed and tended, causing damage, and 3) beam spray in or above plenum airways, where air velocity and vibration may degrade the coating surface and produce fibers. Often, one or a combination of these situations makes the presence of asbestos-containing beam spray enough of a hazard to warrant removal. Beam sprays are sometimes not able to support the additional weight of encapsulation.

B. CEILING ACOUSTICAL TEXTURE

Ceiling acoustical sprays consist of a bumpy material, such as mica or plastic foam and a white mineral powder binder. Chrysotile asbestos was sometimes added to the binder. These materials are used to cover up construction defects and irregularities in ceilings (sometimes walls) and to soften the acoustical properties of an area. These types of material could contain asbestos until 1973, when sprayed asbestos-containing materials were banned in new construction.

Asbestos-containing acoustical sprayed-on ceiling material is currently considered to present relatively little hazard when undamaged and in good condition. The small percentage of asbestos fibers that are present are coated with and somewhat bound in the matrix of the texture. Few fibers will escape from the binder under normal conditions. Therefore, one of the options open to an owner of such a ceiling is to leave it in place. However, the continued presence of such a ceiling does allow for fibers to be released in several common ways: 1) whenever the ceiling is brushed, hit, bumped, or an attempt is made to clean it, the matrix or binder will be disturbed and fibers will be released. Large numbers of fibers can be released during installations in the ceiling, such as hanging plants, ceiling fans, vents, etc. In families having small children, the ceiling can be bumped on a regular basis by balls and other toys, exposing children, those most vulnerable due to the long latency period of asbestos disease, to asbestos. 2) A roof leak can water-soak the texture. If the soaking is extensive, the entire texture can delaminate or separate from the substrate wallboard, causing slabs of asbestos-containing debris to fall to the floor, with an associated massive release of fibers. 3) Finally, over time, the binder of the texture will normally deteriorate slightly. Therefore, even in an undamaged ceiling in good shape, the number of fibers being released will increase with the age of the ceiling.

Acoustical ceilings are often amenable to encapsulation, a simple paint layer being sufficient to prevent fibers from escaping. However, fiber release from bumping or water damage is still possible even when encapsulated. Removal of ceiling coatings involves sealing the area, wetting the material and scraping, and it an expensive proposition.

C. JOINT COMPOUND AND WALL TEXTURE

Joint compound or wall mud is a material consisting primarily of white mineral powder. It is applied as a slurry to smooth joints between wallboard and to eliminate irregularities and nail depressions in walls. Wall texture is a similar material which is usually sprayed but can be trowelled onto walls to produce a pleasing, defect-hiding texture. These types of materials commonly contained chrysotile asbestos from 1945-1975.

Since walls and ceilings patched and textured with these materials are usually painted, the presence of asbestos-containing joint compound or wall texture presents little, if any, hazard. Therefore, in the vast majority of cases, such materials are left in place and as is. In fact, a poorly designed removal attempt is more likely to create a hazard than remove one in this case. However, occupants or custodians of a building containing these materials should be made aware of their presence and potential health effects, since drilling a hole in a wall or any other disturbance of the wall surface could result in a significant number of fibers becoming airborne. Especially hazardous would be sanding a wall to smooth it.

Since there is rarely enough of a hazard due to joint compound or wall texture to warrant removal during occupation of a building, most buildings will reach the end of their lifetime with these materials present. NESHAP allows joint compound to be analyzed with its associated wallboard, and only regulates such wall composites that contain greater than 1% asbestos (and covering more than 160 square feet of area).

D. FLOORING

Flooring, including floor tile, sheet goods, resilient tile and linoleum commonly contained asbestos from the 1920’s until the 1980’s. At present, it still may be present in new tile, even though most large manufacturers have eliminated asbestos from their formulations. Floor tile and linoleum usually contain asbestos throughout, so as they wear or abrade, fibers can be released. Sheet goods and resilient tile have a polymer-like top layer underlain by a spongy, friable fibrous layer. In asbestos-containing sheet goods, this fibrous layer can contain up to 40% chrysotile asbestos. Naturally, the underlayer is only exposed if the flooring is damaged.

Asbestos-containing floor tile and sheet flooring is considered to be of minimal hazard when in good condition, since the fibers are held very tightly in the vinyl or polymer matrix. Therefore, unless it is damaged, powdered, or deteriorated in some way that allows fibers to escape, floor tiles can be left in place almost indefinitely with little or no hazard to inhabitants. The only care needed is an occasional inspection for damage and abrasion. Waxing would tend to seal the floor further against fiber release.

Flooring will usually not fall under NESHAP, even if it covers more than 160 square feet. It is NESHAP Non-friable Category I. That is, only if the tile or flooring will become abraded or crushed during a renovation or demolition, will the renovation or demolition be required to be an abatement. A dry removal using a “chipper” might very well result in the release of fibers from a floor tile, whereas removal of the same tile by lifting the entire tile with solvent would not release fibers.

E. MASTIC

Mastic is a sticky substance used for cementing purposes. Mastic is a non-drying-type substance which is still tacky or flexible after setting up, while glue (discussed below) drys to brittleness. Mastics have contained asbestos from the 1920’s to the present.

Older mastics are tar or asphalt-based and black in color. About half we have tested contain chrysotile asbestos. Newer mastics are polymer or latex based and may be yellow or white. These colors of mastics usually have not been found to contain asbestos, except by contamination from some other material.

By definition, mastics remain tacky over time, as so would not be expected to produce fibers even if exposed. They are NESHAP Category I Non-friable. Therefore, unless exposed, weathered or worn, they do not represent a significant hazard to occupation. They would not be expected to become friable except in the most destructive demolition, and will therefore usually not be regulated under NESHAP. Even if their removal is not regulated by NESHAP, they must be disposed of properly.

F. HARD GLUE

This category refers to those adhesives which dry or cure to become brittle. They are usually encountered on baseboard vinyl moldings and on glued-on ceiling tiles. They have been found to contain chrysotile asbestos as well as anthophyllite, tremolite and actinolite. Asbestos can still be used in their formulation.

In place and undisturbed, these materials are non-friable (NESHAP Category II) and usually not exposed to wear or air currents. Therefore, they pose no threat of fiber release under normal conditions. They are brittle, however, and when damaged or disturbed (molding ripped off the wall, for instance), they will become friable and possibly release fibers. Whether they fall under NESHAPS is decided on a case by case basis. Therefore, if glued-on ceiling or moldings are to be removed during a remodeling or renovation, it depends on the material involved and the type of work to be done to determnine whether the area should be sealed and the removal needs to be performed as an abatement. If a building containing this type of glue is to be demolished, it is possible, but not likely in the current thought, if more than a cubic meter of the glue is present, that the glue would be regulated by NESHAP and therefore have to be abated before demolition can proceed.

G. CEILING TILE

Ceiling tile occurs in two types of installation: dropped or suspended and glued on. Dropped ceiling panels are usually 2’x4′ or 2’x2′ in size and held in place by metal strips, which are, in turn, suspended from the roof by wires. Glued-on ceiling tiles are usually 12″x12″ and glued to drywall ceiling panels. In this section of the country, ceiling tiles rarely contain asbestos, but are occasionally found to contain about 5% amosite or chrysotile asbestos. In other parts of the country, asbestos-containing ceiling tiles are much more prevalent, being used until the middle 1970’s. Ceiling tiles are universally friable. Even if their faces are painted to non-friability, their backs and sides are not painted and remain friable.

Glued-on asbestos-containing tiles may represent little hazard if in good condition, well-adherred and painted. In such a permanent installation, few fibers, if any will be released.

Dropped or suspended ceiling tiles, by the very nature of the installation, are constantly being moved, disturbed and abraded, as they provide access to piping and wires above them. In addition, the space above a suspended ceiling is often a plenum, the return air system for the building, so that building air is constantly circulating (sometimes at high velocities) over the back surface of the tile. For these reasons, suspended asbestos-containing ceiling tiles are usually considered a significant hazard to occupants regardless of their condition. Since they are easily pulled out, removal is the treatment of choice, under controlled conditions, of course.

If a suspended ceiling occurs under an asbestos-containing beam spray, enough beam spray could drop over the years to consider the tiles to be irreversibly contaminated. Therefore, if a beam spray is being removed, new tiles are always placed back, and the old discarded (since the old tiles are unlikely to have enough contamination to exceed the 1% level, they usually do not have to be disposed of as asbestos waste).

H. PIPING OR THERMAL SYSTEM INSULATION

Asbestos-containing insulation was used on both hot piping systems and cold piping systems from approximately the 1920’s through 1975. Commonly found are straight run lagging, elbow packing, and boiler lagging. The insulation materials in themselves are friable and can contain large percentages of either serpentine or amphibole asbestos. However, they are usually covered and held in place by wrapping. The wrapping is customarily painted cotton canvas, which is considered to be a form of encapsulation. Therefore, if the wrap is in good condition, the pipe insulation is considered to not be a significant hazard to those workers even in daily contact with it. The workers must be aware, though, of what lies behind the wrap and the possible health consequences of breaching the wrap, or allowing the wrap to deteriorate. If the pipe insulation is high in amphibole asbestos (more toxic than chrysotile asbestos), any damage to the wrap is intolerable and cause for immediate repair. Extensive damage, such as deterioration of the wrap or break-up of lagging would indicate removal as the treatment of choice.

Another asbestos-containing material related to piping systems is duct wrap or tape. Used during the same period of time as asbestos pipe insulation, white, chrysotile-containing duct tape was used to seal metal air ducts, seams in exhaust vents, and components of furnaces and boilers. It is slightly friable when first installed and becomes more friable with age. The fibers in it are usually long, so it does not tend to powder and produce airborne dust and fibers readily. This, coupled with the small extent of the typical usage make it a minor source of hazard in mechanical rooms and above ceilings. Fiber release can readily be eliminated in most cases by covering the tape with a thick layer of asphalt paint or tar. NESHAP would not require removal of duct tape unless the amount in a building exceeded 160 square feet.

Asbestos-containing fabric was used as a vibration-damping material between air-handling equipment and ducts. Even though the fibers used in fabric weaving are necessarily long and therefore not prone to becoming airborne under normal conditions, the conditions at vibration damping material are not normal. Vibration tends to fragment fibers, and the air streaming by the material tends to pull fibers from their matrix. Little data exists as to the number of fibers released from vibration damping material, but the above considerations indicate that the material may represent a hazard to occupants. Therefore, my recommendation for this type of material is to take the safest action and remove it.

I. ROOFING

Asbestos, usually chrysotile in combination with bitumen (tar or asphalt) and mineral fillers, has been used in roofing and tarpapers up to the present, although most roofers no longer employ asbestos-containing materials.

Bitumen-based asbestos-containing roofing materials usually fall into the non-friable category. Even if weathered to friability, such roofing generally presents little or no hazard to building inhabitants, and its asbestos content is only a consideration during removal or re-roofing. If roofing can become friable during the removal or re-roofing, then NESHAP applies and the work must be done under controlled conditions by qualified personnel.

3. A LIMITED SURVEY

AHERA legislation (1986) provided rules for asbestos surveys. The rules yield a survey with a >95% chance of finding and documenting every source of asbestos in a building. Such surveys will cost thousands even for relatively small buildings. Therefore, surveys for lenders and homeowners are usually less thorough and are termed “limited”. A limited survey involves fewer samples (usually 1-3 per suspect material, rather than 3-7) than AHERA), and no maps of asbestos occurrences.

Since various buildings (and even various parts of buildings) may have been constructed at different times, some would have been built when asbestos was used heavily in construction materials, and some of the newer ones would have been built when many uses of asbestos in building materials had been banned. Therefore, the first step in a survey is to document the year(s) of construction and remodeling for each structure to be inspected. Once a year of construction can be definitely established, sampling of certain materials may be eliminated.

For each building, a walk-through inspection is then performed, in which representative portions if not all areas of construction are visited and observed. Sometimes accessible areas may be assumed to be representative of inaccessible areas of the same era construction. Hidden areas, such as attics, crawl spaces, under carpets and behind tiles are checked when not too destructive.

Samples are taken of materials that could contain asbestos. The sampling method employed is a modified grab sampling. In this method, samples are taken as the material is observed, with multiple samples being taken of materials covering large areas or of materials suspected of being inhomogeneous. The number of samples taken and locations is left to the discretion, experience and judgement of the inspector. It is up to the inspector to fully sample all possible phases of construction and suspect materials within each phase. Unfortunately, this does not guarantee that all occurrences of asbestos will be found. However, the alternative, random sampling, in which the location of samples is determined by chance, does not guarantee finding everything, either, and would be much more costly.

The location and identity of each sample is documented, on a map or plan of the building if one is available, by identity of a room or general locality if a map was not available. The samples are then analyzed at Fiberquant using the EPA “New” or “Improved” Method #600/R-93/116 (unless requested to use the “Interim Method”), which includes polarized light microscopy with optical dispersion staining. The detailed, written report for each sample is attached to each building report. Summaries of the asbestos-containing occurrences are given in each report. Recommendations for treatments of each occurrence are given in each report as well. Where feasible, Asbestos Occurrence Maps, indicating the extent of each asbestos-containing material throughout the building, are given in each report.

 

4. Your House Probably Has Asbestos If …

  • it was built 1955-1978 and has ceilings that are bumpy, as if coated with cottage cheese or popcorn
  • it was built 1940-1955 and has hard, rock-like shingles or siding
  • it was built 1940-1983 and has vinyl flooring
  • it was built 1955-1978 and has gypsum drywall walls
  • it has ductwork sealed with white duct tape
  • it has steam lines
  • it has pipe insulation that looks like corrugated cardboard
  • it was built 1920-1978 and has pipe insulation that is wrapped in canvasTo know for sure, samples must be taken (preferably by a person trained to do so) and analyzed in a laboratory (preferably one that is accredited to perform PLM analysis for asbestos). The results will indicate whether the material is positive (>1% asbestos) or negative (=<1%)

Elwood Caldwell

Welcome to fiberq.com! I'm Elwood Caldwell, and I'm absolutely passionate about all things IT and VR technology. From the intricate workings of computer systems to the immersive experiences of virtual reality, I find myself constantly fascinated by the ever-evolving landscape of these fields. At fiberq.com, I'm thrilled to have the opportunity to share my passion with you. Through articles, news updates, and insights, I aim to provide readers with valuable information about the latest advancements, trends, and breakthroughs in IT and VR technology. Stay tuned for the latest updates and discoveries right here on fiberq.com! Facebook / Email